Sketch: RawSamplesTool_6chan.ino First results for my new 3-phase PCB. All three transformers are connected to a single phase supply. The sensitivity of the voltage sensors have been boosted by altering the reduction ratio after the transformer. The sensitivity of the current sensors have been doubly reduced w.r.t. the normal situation because: a) the processor is running 5 V rather than 3.3 V; b) I've reduced the burden value from 150 R to 120 R. 1st run: No signal at any current sensor 2nd run: 2 kW at the current sensor for L2 According to these results, there is ZERO cross-talk into the current sensors for L1 and L3. With all three voltage sources being in sync, that's quite a result :) RAE, 22/7/14 * * * >>free RAM = 735 millis() now = 3000 recordingMayStartAt 8000 4 3 2 1 0 No of cycles recorded = 1 cycleCount 252, samplesRecorded 28 | 50 2 4 | | 5. 0 2 4 | | 5. 0 2 4 | | 5. 02 4 | | 5. 0 24 | | 5. 2 4 | | 5. 24 | | 5. 4 | | 5. 4 | | 5. 4 2 0 | | 5. 4 2 0 | | 5. 4 2 0 | | 5. 4 2 0 | | 5.4 2 0 | | 4 2 05. | | 4 2 0 5. | | 4 20 5. | | 42 0 5. | | 4 2 0 5. | | 420 5. | | 42 5. | | 4 5. | | 4 5. | | 0 2 4 5. | | 0 2 4 5. | | 0 2 4 5. | | 0 2 4 5. | | 0 2 5. | min_V1 84, max_V1 940, min_I1 511, max_I1 511 min_V2 84, max_V2 939, min_I2 511, max_I2 511 min_V3 85, max_V3 938, min_I3 511, max_I3 511 Raw data from stored cycle: ,[cr] 28, <<< No of sample pairs 519,511 604,511 685,511 757,511 822,511 883,511 925,511 937,511 940,511 936,511 863,511 776,511 680,511 587,511 490,511 410,511 330,511 258,511 193,511 135,511 96,511 86,511 84,511 88,511 166,511 251,511 346,511 439,511 millis() now = 46460 recordingMayStartAt 51460 4 3 2 1 0 No of cycles recorded = 1 cycleCount 552, samplesRecorded 28 | 50 3 4 | | 5. 3 0 2 4 | | 5. 3 0 24 | | 5. 3 024 | | 5. 3 0 2 4 | | 5. 3 024 | | 5. 3 04 | | 5. 3 4 | | 5. 3 4 | | 5. 3 4 2 0 | | 5. 3 4 2 0 | | 5. 3 4 2 0 | | 5. 3 4 2 0 | | 54 2 0 | | 4 2305. | | 42 0 3 5. | | 4 20 3 5. | | 4 20 3 5. | | 42 0 3 5. | | 420 3 5. | | 40 3 5. | | 4 3 5. | | 4 3 5. | | 0 2 4 3 5. | | 0 2 4 3 5. | | 0 2 4 3 5. | | 0 2 4 3 5. | | 0 2 53 | min_V1 94, max_V1 929, min_I1 511, max_I1 511 min_V2 95, max_V2 928, min_I2 376, max_I2 647 min_V3 95, max_V3 928, min_I3 511, max_I3 511 Raw data from stored cycle: ,[cr] 28, <<< No of sample pairs 518,511 604,511 683,511 755,511 818,511 875,511 916,511 926,511 929,511 923,511 851,511 766,511 675,511 584,511 490,511 408,511 330,511 262,511 197,511 144,511 106,511 96,511 94,511 101,511 177,511 261,511 353,511 441,511